Table of Contents
- 1 How many amps does a 5hp submersible pump draw?
- 2 How much current is needed for a 5hp motor?
- 3 How many amps does a submersible pump need?
- 4 How do I know what AMP my well pump is?
- 5 How many amps does a 1.5 hp submersible pump?
- 6 How much power do I need to run a submersible pump?
- 7 How much HP does a motor need to run at full load?
- 8 What is the unit consumption of 3 hp motor in 24 hours?
How many amps does a 5hp submersible pump draw?
Franklin 5 HP Deep Well Submersible Pump Motor,3-Phase,3450 Nameplate RPM,230 Voltage – 2343178602
Item | Deep Well Submersible Pump Motor |
---|---|
Full Load Amps | 15.9 |
Max. SF Amps | 17.8 |
Hz | 60 |
Motor Service Factor | 1.15 |
How much current is needed for a 5hp motor?
Full-Load Current in Amperes Single-Phase Alternating Current Motors
HP | 115V | 230V |
---|---|---|
5 | 56 | 28 |
7-1/2 | 80 | 40 |
10 | 100 | 50 |
The voltages listed are rated motor voltages. The listed currents are for system voltage ranges of 110 to 120 and 220 to 240. |
What is the voltage required for submersible pump?
Most submersible well pumps are 230 volts and require a 2 pole circuit breaker (2 individual circuit breakers connected together).
How many amps does a submersible pump need?
A 1 HP submersible pump engine will draw a 3.2-amper current if it is a single-phase motor at 230 volts of voltage. If it is a three-phase motor at 440 volts, it will draw a maximum 1.7-amper current.
How do I know what AMP my well pump is?
Divide the wattage by the voltage to find the current. For example, if the pump wattage is 2,200 watts, and the voltage is 110 volts, the current is 2,200 /110 = 20 Amps. This is the value of the amps drawn by the well pump.
How many kVA generators are required for a 5 hp motor?
Use of Engine Driven Generators – Single-Phase or Three-Phase
Motor Rating | Minimum Rating of Generator | |
---|---|---|
HP | KW | Internally Regulated |
5 | 3.7 | 7.5 |
7 1/2 | 5.5 | 10 |
10 | 7.5 | 15 |
How many amps does a 1.5 hp submersible pump?
A 1.5 HP motor at full load will produce 1.5 HP, which is just over 1100 watts. if we assume 90\% efficiency, it will consume just over 1200 watts. On a 110 volt supply this equates to about 11 amps. On a 230 volt supply this is a little over 5 amps.
How much power do I need to run a submersible pump?
If there’s no power on site, you need to spec a generator: •Most submersible pumps with 5HP or less are 230V/single phase. You’ll need 1.5kW per motor HP So…a 5HP pump needs a minimum of 7.5kW You also need to spec the right power cable •PVC flat-jacketed wire is the most common.
How many Watts Does a 3 hp motor use?
Take efficiency of 3 HP motor as 80\%. Each HP is 746 watts Therefore 3 HP – 3x 746 = 2238 watts. Take efficiency of 3 HP motor as 80\%. Each HP is 746 watts Therefore 3 HP – 3x 746 = 2238 watts. As you get bill for a month the tariff rate per unit may vary based on slab of no. of units. this need to be considered for calculation purpose.
How much HP does a motor need to run at full load?
7.5 HP motor need not run at full rated load ever. It all depends on load. If I have to design a machine load of 5.5 HP, I may opt for 7.5 HP motor as this is the next higher rating of motor. Again, this 5.5 HP machine will not run at its full rated load, and you cannot judge energy consumption from motor rating.
What is the unit consumption of 3 hp motor in 24 hours?
Unit consumed = Power in kW X numbers of hours of operation. = 59.76 units. Hence units burnt (consumed) by 3 HP motor in 24 hours will be 59.76, if the motor efficiency is 90\% and motor is fully loaded. In actual, motor load will be less than full load and units consumed will be less accordingly.